题目
根据网络拓扑和需求说明,完成路由器R1的配置。
R1 (config)# interface Serial 1/0
R1 (config-if)# ip address (3) 255.255.255..0 (设置串口地垃)
R1 (config-if) #no shutdown (开高串口)
R1 (config) #interface FastEthernet0/0
R1 (config-if) #ip address (4) 255.255.255.0 (设置以太口地址)
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.0.0.1 (5) area 0
R1(config-router)#network 192.1.1.1 (6) area 0
(3)
第1题
【问题2】(6 分)
根据网络拓扑和需求说明,完成路由器R1的配置。
R1(config)# interface Serial 1/0
R1(config-if)# ip address (3) 255.255.255.0 (设置串口地址)
R1(config-if)#no shutdown (开启串口)
R1(config)#interface FastEthernet0/0
R1(config-if)#ip address (4) 255.255.255.0 (设置以太口地址)
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.0.0.1 (5) area 0
R1(config-router)#network 192.1.1.1 (6) area 0
第2题
【问题2】(6 分)
根据网络拓扑和需求说明,完成路由器R1的配置。
R1(config)# interface Serial 1/0
R1(config-if)# ip address (3) 255.255.255.0 (设置串口地址)
R1(config-if)#no shutdown (开启串口)
R1(config)#interface FastEthernet0/0
R1(config-if)#ip address (4) 255.255.255.0 (设置以太口地址)
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.0.0.1 (5) area 0
R1(config-router)#network 192.1.1.1 (6) area 0
第3题
根据网络拓扑和需求说明,完成(或解释)路由器R1的配置。
Router(config) ipv6 unicast-routing (3)
Rl(config) interface Serial 1/0
R1(config-io (4) address (5) (6) (设置串口地址)
R1(config-if)no shutdown (开启串口)
R1(config)interface FastEthemet0/0
R1(config-if) (7) address (8) (设置以太口地址)
R1(config-if)exit
(3)
第4题
【问题2】 (8分)
根据网络拓扑和需求说明,完成(或解释)路由器R1的配置。
R1#configure terminal ;进入全局配置模式
R1(config)# interface ethernet0 :进入端口配置模式
R1(confg-if)# ip address (3) (4) ;配置端口IP地址
R1(config-if)# ipv6 nat ; (5)
R1(config-if)#interface ethernet1
R1(config-if)# ipv6 address (6) /64
R1(config-if)# ipv6 nat
R1(config) #ipv6 access-list ipv6 permit 2001:aaaa::1/64 any ; (7)
R1(config) #ipv6 nat prefix (8)
R1(confg) #ipv6 nat v6v4 pool ipv4-pool (9) (10) prefix-length 24
R1(config) #ipv6 nat v6v4 source list ipv6 pool ipv4-pool
R1(config) #exit
第5题
根据网络拓扑和要求说明,完成(或解释)路由器R1 的配置:
R1#config
R1(config)# interface FastEthernet 0/1
R1(config-if)#ip address (1) (2)
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#ip dhcp pool vlan 3
R1(dhcp-config)#network 192.168.3.0 255.255.255.0
R1(dhcp-config)#default-router 192.168.3.254 255.255.255.0 ; (3)
R1(dhcp-config)#dns-server 192.168.2.1 ; (4)
R1(dhcp-config)#lease 0 8 0 ; (5)
R1(dhcp-config)#exit
R1(config)#ip dhcp pool vlan 4
R1(dhcp-config)#network (6) (7)
R1(dhcp-config)#default-router 192.168.4.254 255.255.255.0
R1(dhcp-config)#dns-server 192.168.2.1
R1(dhcp-config)#lease 0 8 0
R1(dhcp-config)#exit
R1(config)#ip dhcp excluded-address (8) (9)
R1(config)#ip dhcp excluded-address 192.168.3.254
//排除掉不能分配的IP 地址
R1(config)#ip dhcp excluded-address 192.168.4.254
R1(config)# (10) 192.168.3.0 255.255.255.0 FastEthernet0/1
//在以太网接口和VLAN3 间建立一条静态路由
第6题
以下是路由器R1的部分配置,请完成其配置,或解释配置命令含义。
!
R1 (Config) interface fastethernet0
R1(Config-if) ip address (6) (7)
R1(Config-if) (8) (开启端口)
!
R1 (Config) interface serial 0
R1(Config-if) ip address (9) (10)
!
R1 (Config) ip routing
R1 (Config) router rip (11)
R1 (Config-router) (12) (声明网络)
R1 (Config-router) (13) (声明网络)
R1 (Config-router) (14) (声明网络)
R1 (Config-router) version 2 (15)
!
第7题
【问题1】(4分)
根据网络拓扑和要求,解释并完成路由器R1上的部分配置。
R1 (config)#crypto isakmp enable (启用 IKE)
R1 (config)#crypto isakmp (1) 20 (配置 IKE 策略20)
R1 (config-isakmp)#authentication pre-share (2)
R1 (config-isakmp)#exit
R1 (config)#crypto isakmp key 378 address 192.168.2.2 (配置预共享密钥为378)
R1 (config)#access-list 101 permit ip (3) 0.0.0.255 (4) 0.0.0.255
(设置 ACL)
……
第8题
以下是路由器R1的部分配置。请完成配置命令。
Rl(config)interface fastethemetO/0
R1(config—if)ip address(12)(13)
R1(config—if)ip nat inside
R1(config)interface fastethernetO/1
R1(config—if)ip address(14)(15)
R1(config—if)ip nat outside
第9题
阅读以下关于RIP动态路由配置的技术说明,结合网络拓扑图回答问题1至问题3。
[说明]
某大学城局域网的网络拓扑结构如图7-18所示,图中路由器R1、R2,R3均运行基于距离矢量算法的RIP路由协议,并且图中给出了路由器R1、R2、R3各端口的IP地址信息。
结合图7-18所示的网络拓扑结构图,将以下路由器R1配置信息中(1)~(9)空缺处的内容填写完整,实现路由器R1的正确配置。
Router>en (进入特权模式)
Router config terminal (进入配置模式)
Router (config) (1)
R1 (config) no logging console
R1 (config) interface fastethernet0/1
R1 (config-if) ip addtess 192.168.100.1 155.255.255.0
R1 (config-if) (2)
(3)
R1 (config) interface sellal 0 (进入端口S0配置子模式)
R1 (config-if) (4) (设置当前端口IP地址)
R1 (config-if) no shutdown
R1 (config-if) (5)
R1 (eonfig-if) ip address 192.168.65.2 255.255.255.0
R1 (config-if) no shutdown
R1 (config-if) exit (退出当前端口配置子模式)
R1 (config) (6)
R1 (config) (7)
R1 (config-router) (8)
R1 (conhg-router) network 192.168.65.0
R1 (config-router) network 192.168.67.0
R1 (config-router) end (退出回到特权模式)
R1 (9) (将配置信息保存到非易失性RAM中)
第10题
根据网络拓扑和R1的配置,解释并完成路由器R3的部分配置。 R3(config)ctypto isakmp key(7)address(8)
R3(config)crypto transform-set testvpn ah—rod5—hmac esp-des esp-rod5-hmac(9)
R3(cfg—crypto—ttans)exit
R3(config)crypto map test 20 ipsec-isakmp
R3(config—crypto—map)set peer 192.168.1.1
R3(config—crypto—map)set transform-seI(10)
为了保护您的账号安全,请在“赏学吧”公众号进行验证,点击“官网服务”-“账号验证”后输入验证码“”完成验证,验证成功后方可继续查看答案!