The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP？（）

Scope Management:

A.entails managing the project's work content.

B.is a subset of configuration management and as such is performed by CM specialists.

C.is concerned with naming all activities performed, the end products which results and the resources consumed.

D.is not a concern of the project manager.

E.None of the above.

[说明]

下面是某路由器的部分配置信息，解释部分语句的含义。

[配置路由器信息]

Current configuration：

!

hostname router1

isdn switch-type basic-net3 (1)

!

interface Ethernet0

ip address 10.0.0.1 255.255.255.0

ip nat inside (2)

!

interface bri 0

ip address negotiated (3)

ip nat outside

encapsulation PPP

PPP authentication pap callin (4)

PPP multlink (5)

dialer-group 1

dialer string 2633

PPP pap sent-username 263 password 263 (6)

ip route 0.0.0.0 0.0.0.0 bri 0

access-list 2 permit any (7)

dialer-list 1 protocol ip permit (8)

ip nat inside source list 2 interface bri 0 overload (9)

……

End

下面是某路由器的部分配置信息，解释(n)处标有下划线的含义。

【配置路由器信息】

Current configuration：

!

version 11.3

no service password-encryption

!

hostname r1//第(1)处

!

enable password 123456//第(2)处

!

interface Ethemet0

ip address 192.4.1.1 255.255.255.0

!

interface Sefta10

ip address 192.3.1.1 255.255.255.0

encapsulation frame-relay IETF//第(3)处

no ip mroute-cache

bandwidth 4000//第(4)处

frame-relay map ip 192.163.0.2 100 broadcast//第(5)处

frame-relay lmi-type cisco

!

router ospf 1//第(6)处

network 202.1.1.0 0.0.0.255 area 0//第(7)处

network 202.3.1.0 0.0.0.255 area 0

network 202.4.1.0 0.0.0.255 area 0

neighbor 202.1.1.2//第(8)处

!

……

End

A. debug eigrp packets

B. show ip eigrp traffic

C. debug ip eigrp

D. show ip eigrp interfaces

A.OSPF

B.EIGRP

C.IS-IS

D.BGP

A. An EIGRP route will go active if there are no successors or feasible successors in the EIGRP topology table.

B. An EIGRP route will go passive if there are no successors in the EIGRP topology table.

C. DUAL will trigger an EIGRP query process while placing the flapping routes in the holddown state.

D. A feasible successor in the EIGRP topology table can become the successor only after all the query requests have been replied to.

E. The stuck in active state is caused when the wait for the query replies have timed out.

F. EIGRP queries are sent during the loading state in the EIGRP neighbor establishment process.

A. Under t he router eigrp mode add redistribute igrp 123 subnets

B. Under the router igrp mode add redistribute eigrp 123

C. None, EIGRP and IGRP are automatically redistributed in this instance.

D. Under the router eigrp mode add redistribute igrp 123

A. Router# show ip eigrp routes *

B. Router# show ip eigrp summary

C. Router# show ip eigrp topology

D. Router# show ip eigrp adjacencies

E. Router# show ip eigrp neighbors detail

A.OSPF

B.RIP

C.IPX

D.EIGRP