题目
A. frame - relay map commands on R3 - R10 referencing the other routers in this group
B. Nine OSPF neighbor commands on each router
C. Nine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10
D. R1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDR
E. R3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR
第1题
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? ()
A. both routers R1 and R2
B. router R1
C. router R2
D. none of the routers since they are not configured with static RP
第2题
A.The OSPF area is not configured properly.
B.The priority on R1 should be set higher.
C.The cost on R1 should be set higher.
D.The hello and dead timers are not configured properly.
E.A backup designated router needs to be added to the network.
F.The OSPF process ID numbers must match.
第3题
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
第4题
A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.
B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.
C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.
D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.
E. The Hello parameters on routers R1 and R2 do not m atch.
第5题
A.The OSPF area is not configured properly.
B.The priority on R1 should be set higher.
C.The cost on R1 should be set higher.
D.The hello and dead timers are not configured properly.
E.A backup designated router needs to be added to the network.
F.The OSPF process ID numbers must match.
第6题
A. Using an iBGP mesh inside the Enterprise core
B. Configuring default routes in the Enterprise pointing to both R1 and R2
C. Redistributing BGP routes into the Enterprise IGP
D. Tunneling the packets for the i BGP connection between R1 and R2
第7题
A. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned off.
B. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned on.
C. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned on.
D. IBGP session mu st be established between routers R1 and R3, and the synchronization must be turned off.
E. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned off.
F. IBGP session must be established between routers R1 and R3, and the synchronization must be turned on.
第8题
A. router bgp 2
B. router bgp 1
C. neighbor 10.1 .1.2 remote - as 2
D. neighbor 10.1.1.2 Update - source 10.1.1.1
E. neighbor 10.1.1.2 Update- source S0/0
第9题
Routers R1 and R2, currently EIGRP neighbors over their Fa0/0 interfaces (respectively),both use EIGRP authentication. Tuesday at 8 p.m. the neighborship fails.Which of the following wo uld not be useful when investigating whether authenticationhad anything to do with the failure?()
A. debug eigrp packet
B. show key chain
C. show ip eigrp neighbor failure
D. show clock
第10题
A. The redistribution command should be reentered with the match route - type parameter included.
B. The redistribution command should be reentered wit h the route - map map - tag parameter included.
C. The redistribution command should be reentered with the metric metric - value parameter included.
D. Routes will first need to be distributed into another protocol, and then into RIP.
为了保护您的账号安全,请在“赏学吧”公众号进行验证,点击“官网服务”-“账号验证”后输入验证码“”完成验证,验证成功后方可继续查看答案!