Router VE1 has just received a packet and needs to route it. What two actions must this ro

twork. What are some of the advantages of using VE1 to segment the network？ (Choose two)

A. Routers generally cost less than switches

B. Filtering can occur based on Layer 3 information

C. Broadcasts are not forwarded across the router

D. Broadcasts are eliminated

E. Adding a router to the network decreases latency

F. Routers can generally support more LAN ports than switches

A.Which type of server is the target in such an attack？()

B.An e-mail server

C.A DNS server

D.A router

E.A FTP server

A.It checks the configuration register

B.It attempts to boot from a TFTP server

C.It loads the first image file in flash memory

D.It inspects the configuration file in NVRAM for boot instructions

During startup, router VE1 displays the following error message:

boot: cannot open "flash:"

What will VE1 do next？

A. It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.

B. It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.

C. It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.

D. Because of damaged flash memory, the router will fail the POST.

E. It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.

F. None of the above

A.It checks the configuration register

B.It attempts to boot from a TFTP server

C.It loads the first image file in flash memory

D.It inspects the configuration file in NVRAM for boot instructions

r A is the Designated Intermediate System (DIS) at Level 1 for that LAN. Router A‘s DIS priority is 64. The LAN is a Level 1-only link. Router D has just been powered up on that same LAN and its DIS priority is 80.Which statement is true？（）

A. Router A remains the DIS and generates a new pseudonode LSP for that LAN

B. Router A remains the DIS and NO new pseudonode LSP is generated for that LAN

C. Router D becomes the new DIS, generates a new pseudonode LSP for that LAN, and purges the old pseudonode LSP generated by Router A

D. Router D becomes the new DIS, does NOT generate a new pseudonode LSP for that LAN, and does NOT purge the old pseudonode LSP generated by Router A

you to log into router VE1 locally using a terminal emulation program such as HyperTerminal.

A. Connect the PC's COM port to the router's console port using a straight-through cable.

B. Connect the PC's COM port to the router's console port using a rollover cable.

C. Connect the PC's COM port to the router's Ethernet port using a straight-through cable.

D. Connect the PC's Ethernet port to the router's Ethernet port using a rollover cable.

E. Connect the PC's Ethernet port to the router's Ethernet port using a straight- through cable.

F. None of the above

A.Host 1 addresses the frames to the MAC address of router R1

B.Host 1 looks in its ARP cache for the MAC address of router R1

C.Host 1 addresses the frames to the MAC address of web server 2

D.Host 1 sends the packets to router R1 to be forwarded to web server 2

E.Host 1 sends a broadcast ARP request to obtain the MAC address of webserver2

trunk between two switches named VE1 and VE2？ (Select two answer choices)

A. Set each end of the trunk line to IEEE 802.1Q encapsulation.

B. Set the same VTP management domain name on both switches.

C. Set all ports on the two switched as access ports.

D. Configure one of the two switches as a VTP server.

E. Connect the two switches using a rollover cable.

F. Use a router to forward VTP traffic between the VLANs.

u determine that R1 is not able to establish full OSPF adjacency with R2. The show ip ospf neighbor comman d output on R1 shows that R2 is stuck in the INIT state. What could be the cause of this problem？（）

A. DR and BDR election errors between R1 and R2.

B. The R2 router has not received the OSPF hello packets from the R1 router.

C. Mismatched interface ma ximum transmission unit (MTU) configuration between the R1 and R2.

D. Mismatched OSPF hello interval configuration between the R1 and R2

E. Corrupted LSAs exchanges between the R1 and R2.