A Ezonexam Ethernet switch receives a unicast frame. with a destination MAC that is listed

The Ezonexam network Topology is displayed in the exhibit below:

A switch has been configured for three different VLANs: VLAN 2, VLAN 3, and VLAN 4. For the purposes of communication between VLANs a router is to be added. Host from one VLAN should be able to reach the hosts in the other VLANs.

Based on this requirement, what type of connection is acceptable between the router and switch？

(Select all valid answers)

A．10 Mbps Ethernet

B．56 kbps serial

C．100 Mbps Ethernet

D．1,544 Mbps serial

E．1000 Mbps Ethernet

zonexam network. What are two advantages of using Layer 2 Ethernet switches over hubs？ (Choose two)

A．Allowing simultaneous frame. transmissions

B．Increasing the size of broadcast domains

C．Increasing the maximum length of UTP cabling between devices

D．Filtering frames based on MAC addresses

E．Decreasing the number of collision domains

ue about full-duplex Ethernet in comparison to half-duplex Ethernet？

A．Full-duplex Ethernet uses two wires to send and receive. Half-duplex Ethernet uses one wire to send and receive

B．Full-duplex Ethernet consists of a shared cable segment. Half-duplex Ethernet provides a point-to-point link

C．Full-duplex Ethernet can provide higher throughout than can half-duplex Ethernet of the same bandwidth

D．Full-duplex Ethernet uses a loopback circuit to detect collisions. Half-duplex ethernet uses a jam signal

E．None of the above

statement is true about full-duplex Ethernet when comparing to half-duplex Ethernet？

A．Full-duplex Ethernet consists of a shared cable segment. Half-duplex provides a point-to-point link

B．Full-duplex Ethernet uses two wires to send and receive. Half-duplex Ethernet uses one wire to send and receive

C．Full-duplex Ethernet can provide higher throughput than can half-duplex Ethernet of the same bandwidth

D．Full-duplex Ethernet uses a loopback circuit to detect collisions. Half-duplex Ethernet uses a jam signal

E．None of the above

t has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port？

A. This is an Ethernet port operating at half duplex

B. This is an Ethernet port operating at full duplex

C. This is a port on a network interface card in a PC

D. This is 10 MB/s switch port

E. This is a 100 MB/s switch port

F. None of the above

happens when a collision occurs on the network？ (Choose all that apply)

A．Each device on the Ethernet segment stops transmitting for a short time.

B．A jam signal informs all devices that a collision occurred.

C．When data transmission resumes, the devices that were involved in the collision have priority to transmit.

D．The devices that are involved in the collision stops transmitting for a short time.

E．The collision invokes a random back-off algorithm.

ch is being used in the Ezonexam LAN？ (Choose three)

A．Ethernet hub ports are preconfigured for full-duplex mode.

B．The host network card and the switch port must be capable of operating in full-duplex mode.

C．There are no collisions in full-duplex mode.

D．In a full-duplex environment, the host network card must check for the availability of the network media before transmitting.

E．A dedicated switch port is required for each full-duplex node.

and connection losses. After entering the "show interfaces" command, you notice that the Ethernet interface is configured as 100 Mbps full-duplex and that there is evidence of late collisions. What could be the cause of this problem？

A. Duplex mismatch

B. A routing loop

C. Trunking mode mismatch

D. Improperly configured root bridge

E. Improperly configured static VLAN

F. None of the above

net to the local Cisco router using TCP/IP but cannot create a session.

What should you do to resolve the problem？

A. Use a straight-through cable to connect your computer's COM port to the router's console port.

B. Use a crossover cable to connect your computer's COM port to the router's console port.

C. Use a straight-through cable to connect your computer's COM port to the router's Ethernet port.

D. Use a crossover cable to connect your computer's Ethernet port to the router's Ethernet port.

E. Use a rollover cable to connect your computer's Ethernet port to the router's Ethernet port.

F. Use a straight-through cable to connect your computer's Ethernet port to the router's Ethernet port.

G. None of the above

he Engineering Faculty. They're complaining that they're receiving obsolete information from the Business Faculty's network traffic broadcasts.

What can you do to contain the Business Faculty's broadcast while still keeping it connected to the internet and the enterprise services of the University？ (Select all valid answer choices)

A. Use half and full-duplex Ethernet on the Engineering Department LAN

B. Establish a VTP domain to minimize the obsolete traffic

C. Change the switch IP address of the switch

D. Create separate VLANs and subnets for the two departments and route between the two

E. Provide greater bandwidth to the Engineering Department LAN

F. Place the business department on a separate subnet and route between networks