A new Ezonexam switch is installed into an existing LAN and a new VTP trunk is set up with

ched network？ (Select all that apply)

A．Create the VLAN.

B．Name the VLAN.

C．Configure an IP address for the VLAN.

D．Add the desired ports to the new VLAN.

E．Add the VLAN to the VTP domain.

Which of the following need to be completed for the creation of this new VLAN？ (Select all that apply)

A. The EZONEXAM VLAN must be created.

B. The desired ports must be added to the new EZONEXAM VLAN.

C. The EZONEXAM VLAN must be added to all of the domains.

D. The EZONEXAM VLAN must be named.

E. An IP address must be configured for the EZONEXAM VLAN.

F. None of the above. VLAN creations are automatic.

2600 series Cisco router？

A．To boot the IOS from ROM

B．To reset the console password

C．To upload a new version of the configuration file

D．To upload a new version of the IOS

E．To allow a new memory upgrade to be recognized by the router

re allowed over this trunk link？

A. No VLANs

B. Only the VLANs that are specified when creating the trunk

C. Only VLANs 1-64

D. All VLANs

E. All VLAN's except VLAN 1

F. None of the above

of the administrative overhead on your network. You plan on achieving this by configuring a new VLAN for each department in the Ezonexam network.

However, you need to share the VLAN information across numerous switches. Which of the following would allow you accomplish this？

A. STP

B. GVRP

C. SNMP

D. VTP

E. DHCP

F. None of the above

are configured as full-duplex FastEthernet. What is the effect of adding switch ports to a new VLAN on this switch？

A．The additions will create more collisions domains.

B．IP address utilization will be more efficient.

C．More bandwidth will be required than was needed previously.

D．An additional broadcast domain will be created.

E．The possibility that switching loops will occur will increase dramatically.

witch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch？

A．Switch(config)# switchport trunk encapsulation isl

B．Switch(config)# switchport trunk encapsulation ietf

C．Switch(config-if)# switchport trunk encapsulation isl

D．Switch(config-if)# switchport trunk encapsulation ietf

E．Switch(config-if)# switchport trunk encapsulation dot1q

re that the web server is accessible from the Internet. The network uses private addressing, so an IP-to-registered address mapping is required.

To do this, you enter the following command:

Ezonexam(config)# ip nat inside source static 192.168.2.1

198.18.1.254

You unsuccessfully try to ping the Internet from a PC host on the LAN. During the troubleshooting process, you enter the "show ip nat translations" command but the output is blank.

What is the most likely cause of the problem？

A．The keyword overload is missing from the command.

B．The NAT pool must be defined first.

C．An access list must be defined to create static NAT translations.

D．The interfaces must be configured for NAT.

E．None of the above

You are the administrator of Ezonexam's network.

An employee named Mark has a local user account on a Windows 2000 Professional computer. Mark has rights and permissions to multiple files and folders on the computer. All of Mark's permissions are being granted through group membership. Mark recently hired a new employee named Eric as his assistant.

You want Eric to have the same rights and permissions that Mark has on the Windows 2000 Professional computer. You want to accomplish this with the least amount of administrative effort.

What should you do？

A．Create a new local group. Create Eric's user account. Add Mark's user account and Eric's user account to the new group.

B．Create Eric's user account. Copy Mark's profile to Eric's user account.

C．Create Eric's user account. Make Eric's user account a member of all the same groups as Mark's user account.

D．Create Eric's user account. Copy the registry entries in the subkey that correspond to Mark under HKEY_USERS to the subkey that corresponds to Eric.

e purpose of assigning an IP address to a switch？

A．To provide local hosts with a default gateway address

B．To allow remote management of the switch.

C．To allow the switch to respond to ARP requests between two hosts

D．To ensure that hosts on the same LAN can communicate with each other.

E．None of the above