在Windows中,可以通过netsh配置IPv6。在netsh中,显示IPv6地址使用的命令是（)

在Windows Sercer2003中安装IPv6协议使用的命令是

a) Ipv6 install

b) Install ipv6

c) Netsh inp6 install

d) Netsh interface ipv6 install

A.打开Internet信息服务（IIS）。

B.将计算机配置为宿主的缓存客户端。

C.将BranchCache服务配置为自动启动。

D.修改具有高级安全性的Windows防火墙规则。

● 使用Windows提供的网络管理命令 （47） 可以查看本机的路由表， （48） 可以修改本机的路由表。

（47）

A. tracert

B. arp

C. ipconfig

D. netstat

（48）

A. ping

B. route

C. netsh

D. nbtstat

erface”可获得如图7-11所示的系统输出信息，请指出图7-11中“MTU”的含义。另外如想查看该主机IPv6路由表则需要输入什么命令？

e. The server is configured with two network interfaces. You need to configure routing on the server at the branch office. Which two actions should you perform？ （）

A.Install the routing and remote access role.

B.Run the netsh ras ip set access ALL command.

C.Run the netsh interface ipv4 enable command.

D.Enable the IPV4 router routing and remote access option.

ffice. The server is configured with two network interfaces.You need to configure routing on the server at the branch office.Which two actions should you perform？（）

A. Install the Routing and Remote Access Services role service.

B. Run the netsh ras ip set access ALL command.

C. Run the netsh interface ipv4 enable command.

D. Enable the IPv4 Router Routing and Remote Access option.

A.Netsh

B. Secedit

C. Wecutil

D. Wevtutil

erver Core installation of Windows Server 2008 R2.You need to duplicate the Windows Firewall configurations from Server1 to Server2.What should you use？（）

A. the Get-Item and the Set-Item cmdlets

B. the Get-Service and the Set-Service cmdlets

C. the Netsh tool

D. the Sconfig tool

DHCP Server server role and the DNS Server server role. You also have a server named ServerCore that runs a Server Core installation of Windows Server 2008 R2. All computers are configured to use only Server1 for DNS resolution. The IP address of Server1 is 192.168.0.1. The network interface on all the computers is named LAN.Server1 is temporarily offline. A new DNS server named Server2 has been configured to use the IP address 192.168.0.254.You need to configure ServerCore to use Server2 as the preferred DNS server and Server1 as the alternate DNS server.What should you do？（）

A. Run the netsh interface ipv4 add dnsserver "LAN" static 192.168.0.254 index=1 command.

B. Run the netsh interface ipv4 set dnsserver "LAN" static 192.168.0.254 192.168.0.1 both command.

C. Run the netsh interface ipv4 set dnsserver "LAN" static 192.168.0.254 primary command and the netsh interface ipv4 set dnsserver "LAN" static 192.168.0.1 both command.

D. Run the netsh interface ipv4 set dnsserver "LAN" static 192.168.0.254 primary command and the netsh interface ipv4 add dnsserver "LAN" static 192.168.0.1 index=1 command.

A.Windows防火墙

B.WFAS

C.Netsh

D.Netstat